Sash Lock Door Handles
If you're looking to improve the security of your home without compromising aesthetics, go for door handles with sash lock. They can be utilized with a mortice lock or sash lock and can also be combined with an nigh latch to provide extra locking for internal door.
These handles are a combination of two levers mounted on a backplate. They are used with three or five-lever mortice locks. They can be combined with the tube latch.
Lever Lock Handles
There are a variety of lever door handles available to complement any decor. The rustic lever locks are very popular in both farmhouse-style and modern homes. Classic lever handles can be round or spherical, and are easy to hold. They are easy to use and cost-effective and can be incorporated in any style of decor. To create a chic look, opt for polished chrome or a satin nickel handle. These finishes are easy to clean and are durable. Antique bronze and polished Brass are also alternatives. Many handles have a decorative design, like small amber worm eyes or long-horned crystals. Some levers have a pin, star or some other shape that is molded into the bottom.
To change the lever lock door handles you must have the right screwdriver, or tool to remove them. You might require an awl or nail depending on the design and model. Some lever handles feature a narrow notch or hole on one side of the base which can be used to pry it open.
Follow the manufacturer's instructions for removing your handles once you have the correct tool. You'll need to determine the size of the spindle of your new lever handle. Existing doors are often morticed (cut into the door) for latches that were previously used or locks, and need to be fitted to a specific spindle size. Most lever handle manufacturers employ the standard spindle for door handles.
If you are looking to replace a sash lock door handle, take off the handle that was previously used and disconnect the tubular latch bolt from the strike plate that is on the door frame. You will then need to drill a hole into the door frame, then insert the latch bolt through, and connect it to the strike plate in the door frame.
When installing a new lever door handle it is crucial to remember that all ADA (Americans with Disabilities Act) compatible handles are designed to be operated by hand and must not require users to tighten or twist their wrists. To be in compliance with ADA compliance standards, the lever door handle must not be operated with the thumb and finger, or even the entire hand.
Sash Lock Handles
The primary function of door handles for sash locks is to pull the moving sashes together in a tight seal. This helps maintain the interior temperature of the home and prevents drafts. They are also great for doors that don't need the security of keys for locking systems.
Mortice sashlocks are sash locks that combine a deadbolt and latch into one case. They are installed into the door's material. They are used in conjunction with doors with handles and there are a myriad of different options to choose from to fit your home.
Lever lock handle works with a lever on a backplate cut out beneath it, which permits the key to be inserted to operate the mortice sash lock. It's most commonly used for non-locking doors like dining rooms and living spaces however, it can also be used with a tubular lock on a more secure internal door.
These are designed to keep the sash in place at various points, and include a hook that fits inside the keeper. They come in various styles and designs to fit into various types of windows, such as sliding or hinged casement windows. Some are made of cast aluminium, others from brass and even wrought iron. These are available in various finishes to match other elements of door furniture like escutcheons to protect the keyhole.
3 lever sash lock handles can be used on doors inside however they are not suitable for external doors as they don't offer the level of security required by insurance providers. They also have lower resistance to forced entry, which makes them more vulnerable than their certificated 5 lever counterparts.
A door sash with five levers is the best option for doors that are external. It offers higher levels resistance to forced entry and is more difficult to pick or bypass. repairmywindowsanddoors.co.uk feature an upgraded design that has been tested and certified to comply with strict fire, disability and building requirements.
To replace a handle on a sash-lock take the old fastener from both ends by taking out the screws. Make sure you have a screwdriver handy, and carefully separate the pieces to avoid damage. Mark the screw holes with pencil to ensure that you place the new fastener in the correct position when you are ready to put it in place it. Clean any paint or dust flecks, and then screw in the new fastener. Test the handle to ensure it works correctly and creates an airtight seal.
Tubular Latch Handles
The tubular latch is a latch mechanism that is located inside a door, and is operated by turning the handle. It is designed to latch the door shut, but it does not lock the door as mortice locks would. They are usually used on internal doors where no locking is required. They can be fitted with knob or lever handles.
There are a variety of sizes of tubular latches available. The sizes vary from basic to the expensive architectural. The size you pick depends on the usage of the door and whether you require the function of a lock. If you need a thumbturn release mechanism for an emergency, it is necessary to have a lockable latch.
The backset of your door will also influence the latch you choose. You will need to choose a latch that has an backset measurement that is in line with the distance between the edge and the centre of your door's opening for the handle rose or knob. This will ensure that your door knobs or handles operate the latch smoothly.
If you are fitting a spring or unsprung lever or door knob it is essential to select a heavy duty tubular latch that has a double-sprung follower and tongue. This will ensure an effortless action for the latch, and stop it from becoming slow and ineffective with frequent use.
After you have chosen the appropriate latch to meet your needs The next step is to install it on the door. First, make sure that the latch is level with the top of the door frame/casing by taking measurements and marking the position of the latch plate, then drilling holes for it. Countersink drill bits can aid in creating the proper recess so that it can fit comfortably.
After the latch has been installed, you can install it onto the door. Before installing your door handles or locks, it is important to make sure that the latch functions correctly. To do this you need to open and close the door several times. If it is not functioning correctly, try lubricating the door with WD40 before trying it again. If you continue to experience issues, it could be necessary to talk to an expert installer or locksmith.
Keyhole Handles
Keyhole handles work with a tubular lock installed inside the door. This latch is used to open and shut the door. The handle is able to engage the latch when it is pushed down, and releases it when pulled up. These kinds of handles are most often used on internal doors like living rooms and dining room doors but can also be fitted to front doors when paired with a nightlatch.
Door knobs are more contemporary handles that include a sprung lever/handle with an oval or round fixing stem and a matching thumb-turn or escutcheon. They come in various designs and finishes that will fit the doors in your home. They can be used with Euro cylinders or multipoint locking systems for added security. This is achieved by locking the door at several points along the length of the door. Door handles that are compatible require the correct lock center dimension to accommodate the barrel.
A keyhole escutcheon covers the keyhole that is already in the door to conceal it and give the handle a stylish appearance. They can be purchased as either a screw-on or pop-on design, and in a variety finishes to match your door handle. A concealed escutcheon is able to be attached to the door's edge to hide the keyhole and provide a more modern look.
Some handles are compatible with Euro-cylinder locks. These handles are suitable for uPVC doors and require handles that have the Euro cylinder hole as well as screw holes in the backplate. These handles will also require a Euro Cylinder escutcheon, or a standard escutcheon, based on the purpose.
It's important to know the differences between a mortice lock or mortice lock and a tubular latch and the compatibility requirements for each. You will need to take into consideration the door's thickness and the door hinges as well as the frame reinforcements. the size of the backplate to the handle, the lock centre dimensions and the screw centres on the cylinder.